A black screen with sound on your Bush TV is caused by a backlight failure in about 60% of cases, which you can check by shining a flashlight on your screen. If you see faint images, then either the backlight or power board has gone.

WHY IS THERE NO PICTURE BUT SOUND?
The most common cause is a blown backlight or burned-out component/loose cable on the power board or T-Con. You can check which of these is most likely by following the steps below.

You can jump to the relevant part of this guide from the links below, but before you do, I would recommend starting with a few simpler troubleshooting steps to confirm that there isn’t a software or HDMI issue.

2-Minute Troubleshooting – Black Screen With Sound

---

How to Fix a Bush TV With Sound But No Picture

For a quick overview of the troubleshooting steps, you can take a look at my video below, with the full details for each step in this guide.

---

1. Change Your Connection Cables

There’s a possibility that an HDMI connection is automatically switching your input, but is only able to deliver the sound portion of the signal.

HDMI problems affect about 5% of users.

This comes down to either a:

• Faulty HDMI cable with a break in it
• Damaged HDMI port with broken pins
• Poor HDMI connection where the cable and connector are not fully making contact

Start by removing all HDMI and other cables apart from your power cable, then switch your TV on.

If you are now getting a picture, then:

1. Take a look at any HDMI or other physical cables that were connected to the back of your TV.
2. If you have any compressed air, use that to clean the contacts both of the cable and in the connector on the TV. If you don’t have compressed air, then blow gently on them.
3. Make sure your TV is off, then firmly push the cables back into their slots on the TV.
4. Switch your TV back on again.

If that hasn’t fixed the problem, then try using a different HDMI input. Most TVs have 3 or 4 HDMI ports.

If you have one that is on a different part of the TV then that would be the best one to try, as this should have a separate connection to the TV’s main board.

If you now have a picture, then you’ll need to troubleshoot your HDMI cables and/or connected devices.

If this doesn’t help, then open up your TV and look at the cables connecting the HDMI port to your main board if appropriate, or follow the connections of the HDMI port on your main board’s PCB, and check any chips you come across with a multimeter.

If your screen is still black but you can hear sounds, then move on to the next step.

---

2. Remove Any Surge Protectors

In about 10% of cases, a fault within your household power supply, or more specifically within the surge protector or smart plug that your TV is plugged into is the cause of the problem.

To thoroughly test your power supply:

1. Unplug your Bush TV from your wall socket.
2. Remove any surge interrupters or smart plugs so that you have a direct line to your wall socket.
3. Plug another large device that you know works into the same socket and check that the new device works as normal. (It’s important that this device draws approximately as much power as your TV, to confirm the socket is fully working).
4. Remove the other device and plug your TV back into this socket.
5. Switch on the power and switch on your TV using the physical power button located somewhere on its case (usually beneath the Bush logo).
6. See if the red light is solid. If so, this means your TV is getting sufficient voltage.
7. If your Bush TV’s red light is flashing 5, 6, 10 times, or more, then repeat these steps with another wall socket to confirm your household electricity supply isn’t a problem.

It’s also sensible to look at your power cable and confirm that there are no knots or kinks that could be impeding the power.

---

3. Reset Your Bush TV to Fix the Black Screen

Although this might seem a basic step, power cycling your TV is often the best way to fix your Bush TV.

About 30% of people who contact me either through email, YouTube, or who leave comments on this site, fix their problem with a power cycle.

To reset your Bush TV:

1. Make sure your TV is switched off and unplug it.
2. Hold down the physical power button on the TV for at least 15 seconds.
3. Wait for at least 2 minutes for any residual power to drain from the TV’s capacitors (which are capable of storing charge for several minutes).
4. Plug your TV back in and try switching it on. You should see a red light if you have been successful.
5. It’s a good idea to try this a couple more times if it doesn’t work at first, as this can sometimes take a few goes to kick in.

Make sure you do wait for the full 2 minutes before plugging your TV back in – you would be surprised how long the components within your TV can hold a charge, and you want to make sure it has fully reset.

---

4. Check for LED Backlight Failure

If none of the simpler fixes have worked for you, then the most likely culprit of your problem is a backlight failure, in either the inverter or backlight itself.

Failure of the LED backlights is by far the most common cause (>60% of cases) if you have NO picture but CAN hear sound.

The backlight inverter powers the backlight of your TV by uprating the standard voltage and current of your home supply to the higher levels required by the backlight.

It’s a very small board in most TV models (although in some is integrated into the power board). Check this board with your voltmeter, and don’t forget to also look at the cable. These boards are only around $10-15 on eBay, so are very cheap to replace if they have failed.

To check for backlight failure:

1. Follow your normal process for switching on your TV.
2. Get right up close to the screen and point the light on your phone or a flashlight directly at the screen.
3. Try changing channels with your remote, or going into the menu.
4. If the backlight is the only part not working, you will see very faint images on your TV screen.

You can see this process in the video below.

If you see faint images, you can be pretty certain that the backlights themselves are the failure point in your TV.

Backlights on modern Bush TVs come in LED strips of varying lengths. Older models used lengths that spanned the entire frame of the TV, but due to cost savings, more recent TVs use a set 16″ LED strip which is connected in series for each row to span your TV.

These cold-soldered connectors are a notorious failure point on Bush TVs but can be easily fixed if you are willing to re-solder a joint yourself.

Equally commonly, the LED backlights themselves can fail. This is due to repeated current overpowering, which over time causes thermal degradation of the LEDs leading to burnout.

You can replace any failed LEDs by ordering new strips for your TV model from eBay (approx. $30) and switching them over yourself.

The problem with fixing the LEDs is that they are located in the most difficult-to-access part of your TV. So if you are not comfortable with a larger repair job, then now is a good time to seek help from a professional.

Note that if you’ve got an edge-lit TV, then you only have two rows of LEDs – one at the top of the panel and one at the bottom, but both follow roughly the same process for replacement.

You need to remove the back panel, remove all of the circuit boards and connectors, then another layer of screws for the front panel, and only when you have fully removed the LCD panel can you get to the backlights.

Before you do any of this though, I highly recommend that you read the next step detailing how to check the internal boards in your TV, as this is relatively quick and easy and it’s a good idea to rule out any other issues with your TV.

If you cannot see faint images with the flashlight test, then you almost certainly have a T-Con or main board issue which I’ll cover below.

After this, I will then cover how to replace the backlights.

---

5. Check Your TV’s T-Con, Main Board & Power Board

The screen going black on your Bush TV but the sound still working is a common indication of either component/cable connection failure within your TV or a failure of the backlights themselves.

If you DID NOT see faint images with the flashlight test, you most likely have a T-Con or main board failure.

In addition to the backlights, there are three main boards inside your TV:

• Timing Control (T-Con)
• Power board
• Mainboard
• And additional boards such as Wi-Fi modules or remote receivers depending on the model.

The Timing Control (T-Con) board is a small PCB board that drives your TV’s panel, sending the signal to each pixel row of your screen using internal clocks to keep each row in sync.

The Main Board is a larger PCB where you plug your HDMI and other connectors into. This does a lot of the work of translating the input into signal, which then goes to the T-Con board.

The Power Board is where you plug in your power cable, and it converts your home electricity supply into a voltage and current that your TV can use.

These boards are hidden away under the back panel, behind the screen, and any can be the cause of no picture in your LCD / OLED TV.

Either the cable connectors themselves can come loose or get covered in grime or dust, preventing a clean contact, or components on the boards can fail, meaning they don’t power the backlight sufficiently or cannot provide a constant picture signal.

CAUTION
Opening up your TV is potentially dangerous due to the risk of electric shock. If you are not confident in your skills, do not proceed.

The first step is to simply check that the internal cables are tightly seated, particularly those between the power board and the backlight. As power to the backlight comes from one cable connected to the power board, if this connection is loose then your backlight won’t work at all.

To access the boards, first, remove the back panel. If you’re not confident doing this, then now is the time to get an expert in. Otherwise:

1. Unplug your TV, hold down the power button, and wait for at least 30 minutes. There are large capacitors in the power board for the backlight and these can hold charge for an extended period.
2. Place your TV face down on a large table or workbench. Make sure there is nothing that can scratch the screen on your work surface.
3. Ground yourself.
4. Open your TV by unscrewing the screws in the back panel. It should come apart in two pieces: front and back.
5. Put the back panel somewhere out of the way and take a look at the circuit boards that have been revealed.
6. You will see a T-Con panel for translating the signal into a TV picture, a power board, and a main board.

Or see this in action in the video below.

The position of the boards will vary by model but will be broadly the same as in the image above.

Start by giving everything a good clean, preferably with compressed air or a non-static brush. It’s possible that dust in the connections can block the signal.

Then, you should be able to remove the ribbon-like low voltage differential signaling (LVDS) cables on the T-Con board by pushing the locking cover down and they will then easily come away from the board. Don’t try to force them out without unlocking them first.

After removing the LVDS cable, take a look at the individual connectors on the ends of the cables, and the connectors in the socket. You are looking for any signs of corrosion, damage, or dust.

The contacts should be a shiny gold or silver color. If they are dull and appear to have a rough, copper-like layer over them, this would indicate oxidation, and therefore a new cable is recommended.

Repeat this process with the remaining cables linking the T-Con, power board, and main board, and then try powering up your TV to see if the problem is still there.

Often, simply cleaning and reseating the cables can fix screen problems.

If you still have a problem, then use this table to see the most likely cause, and you can then skip to the most relevant step in the remainder of this guide.

---

Power Board

Once you’ve tried disconnecting each cable, cleaning their contacts, and reconnecting them, your next step is to confirm which board the fault is on.

If you DID SEE faint images with the flashlight test, you most likely have a backlight failure, but you need to rule out a power board failure before making any repairs.

• Unplug your TV.
• With all your other cables plugged in, unplug the cable linking the power board and main board, circled in the image below.
  • This cable allows the main board to control the backlights. Disconnecting means that the backlights should default to an always-on state and will also disable any error-correcting pathways that can cause the main board to switch off your TV.

• Switch on your TV.
  • If you could see faint images when you did the flashlight test earlier:
    • And if the backlights are now working, then the power board is okay and the problem is either on the main board (most likely the culprit) or T-Con.
    • If the backlights are still not working, then there’s either a failure of a component on the power board or the backlights themselves have failed.
      • You can check the board with a multimeter to confirm this and/or replace the burned-out component or look for a new power board on eBay for around $30.
      • But it’s more likely to be an LED failure on the backlight, which you can check in the next section.
  • If you did not see faint images when performing the flashlight test:
    • If the backlights are working, but you still have no picture, then the problem is either on the main board or T-Con (most likely the culprit).
    • If you still have no picture or backlights, then you could have a double-headed problem, with a backlight failure and a main board/T-Con failure. Continue with the rest of these troubleshooting steps to narrow it down.

If your backlight IS working, you can rule out LED failure and power board failure – the issue must be with your T-Con or main board.

Take a look at the video below for the steps to troubleshoot the power board. See the next section for steps to troubleshoot the LED backlights.

• Note that if your LED backlights have failed, then you will get zero voltage on the power board as it will shut down to prevent further damage.
• If you put the multimeter probes on the LED connectors and then power on your TV, you should see a momentary jump in voltage, however, which is diagnostic of an LED failure.

---

T-Con

The T-Con is the most likely culprit of most TV screen problems, as one or more of its internal clocks failing often results in artifacts appearing on the screen, but with no picture at all, a main board failure is more common.

T-Con issues often show as artifacts or ghosting on screen if the board is failing or cables are loose, and a totally black screen if the board has completely gone.

If your backlight is working and you have sound, you most likely have a T-Con issue.

If your backlight is working, but you do not have sound, you most likely have a main board issue.

If your backlight IS working (but you DID NOT see images with the flashlight test) and you HAVE sound:

• Unplug your TV.
• Reconnect the cable between the power board and the main board.
• Disconnect one of the T-Con cables going to the panel, circled in the image below.

• Plug your TV back in and switch it on.
  • If you have a picture on half the screen, then you almost certainly have a T-Con problem.
• Repeat these steps swapping over which LVDS cable is connected.
  • If there is no picture with this cable (but there was with the other one), then you have a clock failure on the T-Con.
    • This can potentially be solved by using tape to block the LVDS pins on the cable that carries a signal from the failed clock. See the video below for how to do this. This will probably not be successful though, and it would be better to get a new T-Con from eBay for around $30.
  • If the other half of the screen now has a working picture, there is a general failure of the T-Con and it will need to be replaced.
• If you have no picture regardless of which LVDS cable is connected, then you need to double-check that the problem is with your T-Con itself, or the main board.

If the flashlight test DID show faint images and a FAILED backlight, try totally disconnecting the T-Con. If your backlight now powers up, you need to replace the T-Con. If not, you need to replace the main board.

This video shows you how to block the non-working clock signal from a T-Con if you only have a picture from one cable connected.

If you want to be extra thorough, if you have half a picture with one LVDS cable connected but no picture with both connected, then you might want to double-check that the tab connectors are not the cause.

Tab connector problems usually show as vertical lines on screen.

The basic architecture of most TVs from the T-Con to the panel is:

• 2 x LVDS cables connect to the T-Con at one end and 2 x tab connectors at the other end.
• Each tab connector is a small PCB that further processes the signal.
• Multiple small ribbon cables are connected at one end to the tab connectors, and at the other to the panel itself.
• The panel produces your picture but its architecture is not user accessible.

You can see this connection between the T-Con, the tab connectors, and the panel in the image below.

To check your tab connectors:

• Look for any signs of corrosion or damage.
• Look for a loose tab bond between the PCB and the panel.
• Unfortunately, these tab bonds, and therefore the tab connectors, are not user-replaceable, as they are factory-bonded to the panel. Any fault here means that you need a new panel.
• The video below contains a lot more info on troubleshooting these tab connectors, which you might find helpful.

---

Main Board

To localize the problem to the main board, you will need a multimeter to check the individual components and pins on the cable connections.

Next to the cables connecting each board, there should be a list printed onto the PCB showing what each pin does, and the expected voltages for some of them.

In particular, you want to be looking for anything labeled BL_/BLU_, such as BL_ERR or PWM_ for Pulse Width Modulation on more recent TVs.

With your TV unplugged, reconnect all cables. Then turn your TV on and check the voltages with a multimeter.

Be careful not to touch any live components with your fingers. If you are not confident, skip this step.

An easy way to check voltages on cables and their sockets is to cut the leg off an old resistor and wrap this around your multimeter probe. You can then poke the leg of the resistor into each pin’s socket on the board, as otherwise, your multimeter probe is likely to be too wide to only touch one pin at a time.

If you’re seeing high voltages on BL_ERR pins or other BL_ pins, then you can safely assume that your mainboard has a fault, and it’s easiest to simply replace the entire board with a comparable version from eBay – use your TV model number to find one.

The main board is usually implicated in a black screen of death WITHOUT sound, but in some cases can cause a black screen WITH sound.

You can also check the comparable pins on the power board or T-Con if you prefer.

---

6. Replace Backlights

If the flashlight test DID show faint images, and you’ve ruled out problems with the power board, then replace the backlights.

To replace the backlights:

1. Switch off and unplug your TV.
2. Any wires or ribbons that are near the edge of the TV should be disconnected.
3. Then remove the screws around the edge that hold the bezel of the TV.
4. With some care, you should be able to remove the bezel and panel and reveal the TV backlight underneath, which will be in strips of LED lights.
5. Use a multimeter or TV backlight tester (or make your own with a couple of bits of wire and some batteries) to check whether they are working, and replace any failures.

It’s also possible that one of the connectors linking the LED strips as they span the width of your TV has failed. This can be fixed by checking the connectors with a multimeter and re-soldering any broken connections. This article has a good study on this.

If you have an Edge-lit TV, then follow the video below instead.

Bush TV Support & Warranty

It goes without saying that if your TV is under one year old, then you should contact Bush customer support to get it replaced under warranty.

Even if Bush won’t fix your TV, they might still offer you a discount off a future model if you pester them hard enough! This is always worth a try in my experience.

Bush TV Troubleshooting Overview

• The most common cause of hearing sound but having a black screen on a Bush TV is a backlight failure, followed by a power board or main board failure.
• You can check for backlight failure with the flashlight test, and replace the backlights if your picture is okay.
• If you have no picture with the flashlight test, then you most likely have a T-Con or main board failure, but this can be checked by disconnecting each internal board in turn and testing your screen.
• Before jumping into these more complex fixes, first, try power cycling your TV a few times and make sure the issue isn’t caused by HDMI or faulty surge protectors.

I’m confident that these steps will fix your TV, although the later steps do require a bit more effort than the earlier ones.

Don’t forget that opening up your TV will void its warranty, but this can’t be helped in most cases.

If you need any further help, then I suggest contacting Bush support directly or checking on YouTube where it’s much easier to see how to open up your TV, for example.

Read More:

Bush TV not connecting to Wifi?

Bush TV won’t turn on?

My TV says no signal but everything is plugged in

HDR vs HDR10